Eachine Minicube – 20x20mm stack

59,99 

Poista
Tuotetunnus (SKU): Ei saatavilla/-tietoa Osastot: , ,

Kuvaus

1). Eachine Minicube Flysky 8CH AFHDS2A receiver
Channels: 8CH
Model type: Multi-rotor
Frequency range: 2.408-2.475GHz
2.4GHz system: AFHDS 2A
Transfer method: FHSS
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >300m
Working current: 40mA
Size: 27*27*7mm
Mount hole:20mm*20mm
Weight: 3.1g
Ibus output with failsafe

Compatible Transmitter: Compatible with FS-i4, FS-i6, FS-i6S, FS-i6X, FS-i10, FS-GT2E, FS-GT2G, FS-GT2F

2). Eachine Minicube Frsky Compatible 2.4G 8CH Receiver:
Frequency range: 2.403-2.479Ghz
Channels: 8CH
Work mode :D8 Mode
Output: SBUS
Antenna length: 100mm
No ground interference ( Transmitting and receiving 1 m from the ground): >500m
Built-in Buzzer (Low voltage alarm) Configure by Betaflight configurator
Working current: 80mA
Dimensions: 27*27*7mm
Weight: 3.5g
Compatible with FRSKY ACCST
Compatible with X9D(Plus)DJT/DFT/DHT
Telemetry: RSSI, 1S-3S voltage (A1), 1S-3S voltage (A2)
2. Eachine Minicube F3 V1.1 6DOF Flight Controller:
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Working voltage: 2-3S Lipo
Processor: STM32 F303 MCU
Sensor: SPI Sensor MPU6000
Built-in Betaflight OSD (Batt voltage, RSSI, Fly mode, Flytime, Craft name etz.)
Firmware version: Betaflight 3.1 Dshot ready
Target: OmnibusF3
This V1.1 version comes with SH1.0 plug instead of USB interface, intergrated filtration module.
3. Eachine Minicube 10A BLHeli_S 4 In 1 ESC:
Size: 27mm*27mm*5mm
Mount hole: 20mm*20mm
Firmware version: BLHELI_S 16.5
BB2, 48MHZ Chip
Lipo Battery: 2-3S
Con. Current: 10A
Peak Current: 15A (10S)
BEC: 5V @0.1A
Programming: YES
Betaflight passtrough ready
Dshot600 ready(Default)
Support oneshot42 oneshot125 Multishot Dshot
Damped light on
Features:
STM32 F303MCU + BLHELI_S ESC make your Operating feel more stabilly and silky
Jaw-dropping flight performance
LED_STRIP solder pin
BUZZER Ready
Betaflight support
Acro mode / Air mode /Angle mode support
Built-in OSD(Using F3 MCU controls OSD over SPI bus in DMA mode)
OSD Configuration has been include in BETAFLIGHT GUI
Radio Stick to control PID Tunes
Package included:
1 x Minicube Receiver
1 x Minicube F3 V1.1 6DOF Flight Controller
1 x Minicube 10A BLHeli_S 4 In 1 ESC
(This version of flytower comes already soldered)

Lisätiedot

Receiver

FrSky, FlySky